ATP Electronics Launches High-Endurance Video Recording, 512 GB Max. Capacity Memory Cards for AI Surveillance Infrastructures
2024.06.03
Release![](https://kft.kanematsu.co.jp/en/wp-content/uploads/sites/2/2024/05/5e5a405a8c5e782ed305aee7570f8d0b-1024x464.jpg)
ATP Electronics, which Kanematsu Futuretech Solutions (KFT) is the distributor in Japan and the global leader in specialized storage and memory solutions, introduces its new S650Si (TLC) and S750Pi (pSLC) Series SD and microSD memory cards built with 176-layer 3D NAND technology and low-density parity check (LDPC) controller.
With expanded capacity offerings up to 512 GB and 5-year extended supply longevity support, the new memory cards are targeted for growing segments spurred by 5G, artificial intelligence (AI), and edge technologies, such as AI-enabled surveillance, smart homes, mobile monitoring, automotive recorders, remote healthcare, and security surveillance systems requiring heavy write and re-write usage.
High Endurance: Best-in-Class Cost-per-GB Memory Card Solutions
Maximizing SSD lifespan, as well as the availability of replacement units long after similar consumer-grade counterparts have stopped production, is important for business to get the most out of their investments. This is why ATP Electronics is committed to longevity support.
Native TLC mode
High endurance is critical in any non-stop recording environment. With capacities ranging from 64 GB to 512 GB, the S650Si Series is rated for 5K+ P/E cycles and Terabytes Written (TBW) of up to 2,000 TB.
pSLC configuration
For customers requiring an even higher-endurance solution, the S750Pi Series pseudo single level cell configuration offers up to 100K+ P/E cycles and TBW rating of up to 12,670 TB. These memory cards are available in capacities from 16 GB to 128 GB.
Both configurations are I-Temp operable and feature power loss protection technology, making them suitable for systems installed in extreme conditions with temperature shifts from -40°C to 85°C and unstable power supply settings. Compared with previous-generation ATP SD/microSD offerings, the new memory cards also offer 3X faster sequential write and better sustained writing performance.
The graph below shows that based on 13 Mbps (lowest bitrate of HD recording) tested at 128 GB capacity point, ATP’s 176-layer TLC cards do not only deliver extended recording hours compared to competitors with the same storage capacity but also present a cost-effective solution for video recording.
![](https://kft.kanematsu.co.jp/en/wp-content/uploads/sites/2/2024/05/2849ad3b10d48bf2593fc60c968ca095-1024x401.png)
AI Surveillance Infrastructures: We Build With You
With the rapid advancement of AI technology and the proliferation of edge computing infrastructure and applications, ATP is fully capable of addressing diverse, application-specific needs through its mass production infrastructure. ATP-developed firmware and hardware configurations can meet customers’ unique requirements.
ATP SD Life Monitor: Intelligent Workload Inspection
ATP’s SD Life Monitor tool provides “Workload Inspection.” This gives customers a quick look of the write operation and file size by the host systems pre-qualification. The information is presented as a pie graph for ease of monitoring.
Considering the NAND flash page size and FW algorithm, ATP then provides recommendations and more information for the host devices’ program data based on the multiples of minimum data transfer size in SD/microSD card datasheet.
Upon tuning according to workload inspection, ATP’s memory cards exhibited consistent latency performance when compared to untuned memory card solutions.
Stable latency ensures consistent performance even after long-term writing, ensuring good-quality continuous video recording. This is especially important for applications like digital video recorders (DVRs), where unexpected latency can result in frame dropping or low recording quality. In the following graph, ATP’s TLC solutions with optimized latency (blue) maintain stable performance, which ensures high quality real-time video recording even after long-term writing. In contrast, unoptimized solutions (gray) show latency spiking up after a period of programming.
![](https://kft.kanematsu.co.jp/en/wp-content/uploads/sites/2/2024/05/df27fbe87e9e3f1bc62a7ab09a24beb5.jpg)
Joint Validation Service
ATP performs compatibility and function tests using client-supplied host devices and systems to proactively detect and minimize failures that may not have been caught in production tests. Below are joint validation tests optimized according to application needs.
・Software Joint Integration
・Compatibility Study and Test
・Device Signal Measurement
・Function/Performance Enhancement
・Additional tests (e.g., Industrial Standard, Power Cycling Test)
Advanced Card Analysis
System-in-Package (SiP) wafer/die process makes ATP memory cards resistant to water, dust, and shock; however, it also makes it difficult to perform component analysis compared to SMT (surface- mount technology) process. ATP’s uniquely designed substrate and debug tool make post-analysis possible.
Specifications
![](https://kft.kanematsu.co.jp/en/wp-content/uploads/sites/2/2024/05/27bf52dbc262e9f562bbf64fde9a08e0-1024x633.png)
For more information on ATP’s S750Pi / S750Pc & S650Si / S650Sc SD Cards, visit:
Industrial SD Card | 512MB to 512 GB | ATP Electronics (atpinc.com)
For more information on ATP’s S750Pi / S750Pc & S650Si / S650Sc microSD Cards, visit:
Industrial microSD | -40C to 85C operable | ATP Electronics (atpinc.com)
![](https://kft.kanematsu.co.jp/en/wp-content/uploads/sites/2/2022/09/ATP-logo_png_L-1-1-1.png)
For more information
Contact Us